• HOME
  • TKDN IK
  • REKAPITULASI
  • FAQ
  • REGULASI
  • VIDEO
  • REFERENSI
  • HOME
  • SERTIFIKAT TKDN
  • REKAPITULASI
  • FAQ
  • REGULASI
  • REFERENSI

Detail Perusahaan

PT. Fosroc Indonesia
Jl. Akasia II Blok A8 No.1, Delta Silicon Industrial Park, Lippo Cikarang, Kel. Cikarangkota, Kec. Cikarang Utara, Kab. Bekasi, Jawa Barat
Sertifikat TKDN
No. Jenis Produk Spesifikasi Tipe Merk Kelompok Barang Nilai TKDN
1.Brushbond Flxiii Pot life @35°C : Approx. 1.0 hr ; Adhesion to substrate (ASTM D4541:2002) : 1.0 N/mm2 ; Shore A hardness (ASTM D2240:2010) : 79 ; Tensile strength (N/mm2 ) (ASTM D412-2013) : >2.00 N/mm2 ; Elongation at break (ASTM D412-2013) : >300% ; Water Permeability (DIN 1048:Pt 5: 1991) : Nil ; Water vapour transmission (ASTM E96:2005) : ~ 4.64 g/m2.hr ; Crack bridging (ASTM C836-2012) : 2.0 mm Foot traffic : 6 hr +/- 1hr.FLXIII High-technology polymer modified elastomeric waterproofing membrane system for concrete and masonry surfaces-Bahan Kimia dan Barang Kimia72.11
2.Brushbound FlexPot life at 25°C : +/- 60 min. Elongation at break (ASTM D412) : 40 – 70% Tensile strength (ASTM D412) : 1.5 – 1.8 N/mm2 Water permeability (5.09kg/cm2, 72 hrs) : NIL Water absorption (ASTM C642) : < = 0.3% Static Crack Bridging (ASTM 836,ASTM1305): No crack at 2mm widthCementious Water Proofing-Bahan Kimia dan Barang Kimia67.04
3.Brushbound GreyPot Life at 25°C : +/- 60 minutes Available Colour : Grey and White Water Absorption,% ASTM C - 642 < 0.3 Elongation, % : ASTM D638 <10% Permeability (5.09kg/cm2, 72 hrs) : < 2cm Static Crack Bridging (ASTM 836,ASTM1305): No crack at 2mm widthCementious Water Proofing-Bahan Kimia dan Barang Kimia59.51
4.Cebex 100Chloride content Nil to ASTM D512 ; Compressive strength The plasticizing action of Cebex 100 allows reduction of the water/cement ratio of grouts while maintaining flow properties. Setting times Cebex 100 does not significantly affect the setting times of cement based grouts ; Expansion characteristics The controlled positive expansion in unset grouts incorporating Cebex 100 overcomes plastic settlement when measured in accordance with ASTM C827. An unrestrained expansion up to 5% is typical. Time for Expansion 15 mins – 2 hrs @ 20°C ; Compatibility Cebex 100 is compatible with all types of Portland cement.Plasticized Expanding Grout Admixture-Bahan Kimia dan Barang Kimia36.18
5.Cemax 482tnAppearance Light Brown to Brown Liquid Moisture Content Max. 45 % Specific gravity (25+/-2°C) 1.05 – 1.20 pH (25+/-2°C) 8.5 – 10.0Cement Grinding Aids-Bahan Kimia dan Barang Kimia26.18
6.Cemax 486Appearance Light Yellow liquid Shelf Life 12 months Specific gravity 1.054– 1.074 @ T 25 ± 2 °C ; pH 10.50 – 11.50 @ T 25 ± 2 °CCement Grinding Aids-Bahan Kimia dan Barang Kimia44.62
7.Cemtop 100Performnace at water to powder ratio 0.2 and T= 25+/-2°C : Compressive strength, ASTM C109 modif. (air curing)Tolerance + 10% : 14 N/mm2 @28 days ; Flexural Strength ASTM C348 : 3 N/mm2 @28 days ; Minimum thickness : 2 mm ; Maximum thickness 6 mm ; Traffic time: Light Foot traffic 4-6 hours ; Overlay time 24 hours.Cement based, self- levelling, thin layer, underlayment - 2mm to 6mm-Bahan Kimia dan Barang Kimia33.73
8.Conbextra Ep 10 TgCompressive strength ASTM C579-01 >= 70 N/mm2 @ 7 days Density Approx. 1050 kg/m3 Flexural Strength >= 25 N/mm2 Pot life, approx.. 60 min. @ 20°C, 40 min. @ 35°C Viscosity (mix base + hardener) 700 – 1000 cpsLow Viscosity Epoxy Injection Resin-Bahan Kimia dan Barang Kimia32.80
9.Conbextra Ep 120Compressive Strength ASTM C942 60 N/mm2 at 1 day; 110 N/mm2 at 7 days Flexural strength ASTM C348 32 N/mm2 at 7 days Pot life 75 min @ 25°C Fresh Wet Density Approx. 2450 kg/m3High Strenght Epoxy Resin Free Flow Grouts-Bahan Kimia dan Barang Kimia21.40
10.Conbextra Ep 75Compressive strength (ASTM C942), with tolerance 10% : 80 N/mm2 at 1 day, 95 N/mm2 at 3 days, 100 N/mm2 at 7 days Flexural strength (ASTM C348) >=30 N/mm2 at 7 days Tensile strength (ASTM C881) >=14 N/mm2 at 7 days Pot life : 2 hours at 23°C Maximum flow distance for a head of 100 mm at 20°C : 35 mm gap - 2000 mm; 70 mm gap - 3500 mmHigh Strenght Epoxy Resin Grout-Bahan Kimia dan Barang Kimia33.13
11.Conbextra Ep300Compressive strength (ASTM C942) 7 days @35°C : 100 N/mm2 ; Tensile strength ASTM C881 7 days @35°C : 14 N/mm2 ; Flexural strength ASTM C348 7 days @35°C : 30 N/mm2 ; Density : 1950 kg/m³ ; Pot Life : 50 mins at 40°C, 80 mins at 30°C, 100 mins at 20°C ; Chemical resistance : Oil, grease, fats, most chemicals, mild acids and alkalis, fresh and sea waterLow exotherm, epoxy resin free-flow grout-Bahan Kimia dan Barang Kimia16.21
12.Conbextra GpCompressive strength (ASTM C109/C109M) With tolerance 10%: 26 N/mm2 @ 1 day, 55 N/mm2 @ 7 days, 65 N/mm2 @ 28 days Flexural strength (EN 196) tolerance min. 15% : 10 N/mm2 @ 28 days Time for expansion Start : 15 to 20 minutes, Finish : 1.5 to 2 hours Fresh wet density : Approximately 2170 kg/m3 Expansion characteristics ASTM C940 : Up to 2% @ 24 hoursGeneral Purpose Non-Shrink Cementitous Grout-Bahan Kimia dan Barang Kimia72.68
13.Conbextra Gp PremixCompressive Strength ASTM C109/C109M : 25-30 N/mm2 @ 1 day; 55-60 N/mm2 @ 7 days, 65-70 N/mm2 @ 28 days Flexural strength, 28 days SNI-03-4431-1997 : 50 – 60 kg/cm2 Time for expansion Start : ±15 minutes; Finish : ±120 minutes Fresh wet density : Approximately 2270 kg/m3 depending on actual consistency used. Expansion characteristics ASTM C940: Up to 2% @ 24 hoursGeneral Purpose Non-Shrink Cementitous Grout-Bahan Kimia dan Barang Kimia74.02
14.Conbextra GpxtraPerformace at water to powder ratio = 0.16 and T= 25±2°C : Compressive strength ASTM C109/C109M = 40 N/mm2 @ 1 day, 60 N/mm2 @ 7 days, 80 N/mm2 @ 28 days (Tolerance +/-10%) ; Flexural Strength BS EN 196-1 = 10 N/mm2 @ 28 days ; Initial time of expansion 15 – 20 minutes ; Fresh wet density Approx. 2200 kg/m2 ; Expansion characteristics ASTM C940 : Up to 2% ; Initial Set 3.5 hours, Final Set 4.5 hours ;High Strength, High Flow, Non-shrink Cementitious Grout-Bahan Kimia dan Barang Kimia66.62
15.Conbextra HfPerformance at water powder ratio of 0.21, and a temperature of 20°C : Compressive strength ASTM C109 / C109M-13 : 20 N/mm² at 1 day, 50 N/mm²at 7 days, 64 N/mm² at 28 days ; Flexural Strength EN 196-1:2016 : 2 N/mm² at 1 days, 5.5 N/mm² at 7 days, 6 N/mm² at 28 days ; Flow characteristics (Efflux time) CRD-C Cone : 25 - 45 seconds ; Setting time BS4550 Part 3 1978 : Initial set : 5.5 hours, Final set : 7.5 hours, Time for expansion : Plastic state start : 15 minutes - Finish : initial set, Hardened state : Start: initial set - Finish : up to 28 days ; Wet density : Approximately 2100 kg/m3 ; Expansion characteristics: An expansion of up to 2% when measured according to ASTM C-940Non-shrink cementitious, free flow, precision grout-Bahan Kimia dan Barang Kimia51.77
16.Conbextra Hf PremixPerformance at water to powder ratio = 0.13, at T= 25 ± 2°C : Compressive Strength BS EN12390-3. Cube 10x10x1°Cm (Tolerance +/- 10%) : 20 N/mm2 @ 1 day, 48 N/mm2 @ 7 days, 58 N/mm2 @ 28 days; Time for expansion Start : ±15 minutes, Finish : ±120 minutes ; Flow test (concrete slump cone) 60 – 75 cm ; Fresh wet density Approx. 2200 kg/m3 ; Expansion characteristics ASTM C940: Up to 2%.Non-Shrink Cementitous Grout for thickness up to 500 mm in one pouring-Bahan Kimia dan Barang Kimia51.12
17.Conbextra SfCompressive Strength ASTM C109/C109M Tolerance +/- 10% : 30 N/mm2 at 1 day, 55 N/mm2 at 7 days, 70 N/mm2 at 28 days Consistency, BS890 20 – 26 cm Time for Expansion Start: 15-20 minutes, Finish: 1.5 – 2 hours Fresh wet density Approx.2240 kg/m3 ; Expansion characteristics ASTM C940 Up to 2% @ 24 hourDual Expansion, High Strenght Cementituous Grout-Bahan Kimia dan Barang Kimia67.26
18.Conbextra StdPerformance at water to powder ratio 0.22 : Compressive Strength ASTM C109/109M : 10 N/mm2 @ 1 day Tolerance +/- 10%; 35 N/mm2 @ 7 days, 40 N/mm2 @ 28 days ; Time for Expansion : Start 15-20 min, Finish +/- 2 hours ; Fresh Wet Density Approx. 2100 kg/m3 ; Expansion characteristics ASTM C940 : Up to 2%.Non-Shrink Cementitous Grout-Bahan Kimia dan Barang Kimia71.30
19.Conbextra UwCompressive Strength (ASTM C109/109M) Tolerance +/- 10% : 20 N/mm2 @ 1 day, 33 N/mm2 @ 7 days, 40 N/mm2 @ 28 days Density of hardened grout : Approx. 2050 kg/m3Non-Shrink Cementitous Grout For Underwater Application-Bahan Kimia dan Barang Kimia48.77
20.Conplast CwpAppearance : Opaque /White liquid Density at 25+/- 2°C : approx. 1.20 ; Chloride Content : Nil (Not intentionally added) Water permeability : < 5 cm (test method: DIN EN12390-8:2009-07) Water Absorption : < 5% (test method: BS1881:part 122:1983) or ASTM C642Integral Crystalline Waterproofing For Concrete-Bahan Kimia dan Barang Kimia67.67
21.Conplast Sp 377Specific Gravity: 1.15 – 1.17 at 25 +/- 2 °C ASTM C494 Conplast SP337 Type A&F (water reducing and High Range Water Reducing)Superplastisizer Admixture-Bahan Kimia dan Barang Kimia64.33
22.Conplast Wp421Appearance : Brown liquid ; SG at 25+/-2°C : approx. 1.15-1.16 ; Chloride Content : Nil (Not intentionally added) ; Water permeability : < 5cm, test method according to DIN EN12390-8:2009-07 ; Water Absorption : < 5%, test method according to BS1881:Part122:1983 or ASTM C642High Performance Integral Waterproofing For Concrete-Bahan Kimia dan Barang Kimia63.60
23.Conplast X421mAppearance : Brown liquid ; SG at 25+/-2°C : approx. 1.15-1.16 ; Chloride Content : Nil (Not intentionally added) ; Water permeability : < 5cm, test method according to DIN EN12390-8:2009-07 ; Water Absorption : < 5%, test method according to BS1881:Part122:1983 or ASTM C642High Performance Integral Waterproofing For Concrete that contain Hydrophobic Properties-Bahan Kimia dan Barang Kimia51.93
24.Fosroc Concrete RemoverAppearance : Clear to pale yellow liquid ; Density : 1.02 – 1.06 ; pH (1%-w in water) : 1 - 3 ; Solubility in water : SolubleEnvironmental-Friendly Concrete Remover-Bahan Kimia dan Barang Kimia42.03
25.Nitobond ArSlant shear adhesion (BS 6319Pt 4; 1984) : 9.0 N/mm² ; Curing efficiency BS 7542 : 1992 : > 55%Acrylic emulsion primer and bonding agent for concrete repairs-Bahan Kimia dan Barang Kimia73.89
26.Nitobond EcColour (mixed base+hardener) : Grey SG : +/- 60 at 25° Compressive strength (N/mm2), Tolerance +/- 10% ASTM C 579 : 1 days = 60, 7 Days = 80 Pull off test (N/mm2) ASTM D4541 - 17 ; 7 days : >=2.0 (failure on concrete)Two Parts High Strenght Epoxy Bonding Agent-Bahan Kimia dan Barang Kimia19.37
27.Nitobond PvaAllow to tacky (20 to 30 minutes). Allow set for 24 hours. See TDS for more detail specification Multi-purpose resin adhesive, sealer and cement admixture-Bahan Kimia dan Barang Kimia23.32
28.Nitobond SbrCompressive strength (ASTM C109) : 35 N/mm2 @ control 28 N/mm2 Flexural strength : 11.5 N/mm2 @ control 7.9 N/mm2 lant shear bond :18 N/mm2 @ control 2.6 N/mm2 Chemical resistance :Cementitious materials have limited chemical resistance. The addition of Nitobond SBR to cement mortars reduces permeability and therefore helps reduce the rate of attack by aggressive chemicals, acid, gases and water.Polymer Bonding Aid And Additive For Mortars, Screeds And Renders-Bahan Kimia dan Barang Kimia75.45
29.Nitocote Ep 403Volume solids : 100% ; Viscocity : Pourable, spreadable liquid Pot life @ 20°C 30-40 minutes, @ 35°C 10-15 minutes ; The fully cured coating is resistant : Distilled water, Petrol, Xylene, 50% sulphuric acid, Saturated sodium chloride, 50% sodium hydroxideDamp-Tolerant, Solvent Free Epoxy Resin Coating-Bahan Kimia dan Barang Kimia17.47
30.Nitocote Ep 405 Solid by weight @25°C : 100% (mixed) Pot life @25°C:1 Hour 25 minutes, @35°C : 55 minutes Drying time @ 35°C : Touch dry : 3 hrs, Recoatable : 3-12 hrs, Fully cured : 5 days ; Bond strength (ASTM 4541-85) : Substrate failure first at 2 N/mm² Water Absorption (weight) : < 0.1% Chemical resistance ; Acids (m/v) Phosphoric acid1 10% :Very good ; Lactic acid1 10% : Very good Hydrochloric acid 30% :Good Alkalis (m/v) ; Sodium Hydroxide 40% :Excellent Solvents & organics Kerosene :Excellent Petrol1 : Very good Gas Oil1 :Very good ; Nickel Plating Solution1 : Very good Aqueous solutions Distilled water : Excellent Chlorinated water :Excellent Marsh water :Excellent Sewage water :Excellent VOC : 11.3 g/lNon Toxic, Epoxy Resin, Protective Coating And Waterproofing Lining For Concrete And Metal-Bahan Kimia dan Barang Kimia17.15
31.Nitoflor Fc150Properties at ambient Temperature @20°C ; Pot life :40 min Cure time : 24 hrs ; Maximum time between coats : 36 hrs ; Light traffic use after : 24 hrs ; Full traffic use after : 48 hrs ; Resistant to chemical spillage : 7 days ; Mixed specific gravity : 1.42 ± 0.05 ; Compressive strength : 70 N/mm2 ; Flexural strength : *40 N/mm2 ; Tensile strength (ASTM D638-99) : 20 N/mm2 ;Volume of Solids : 100% ; Impact Resistance (ASTM D 2794 : 1996) 9.85 Joules ; Surface Hardness (ASTM D 2240 :1996) : 77-85 Shore D ; Abrasion Resistance (ASTM D 4060 : 1996) : 100 mg /1000 cycles (CS-10), 150 mg/1000 cycles (CS-17) ; Bond strength to concrete : Greater than the cohesive strength of concrete ; Water absorption (ASTM D570-98) : 0.06% ; Reaction to fire (for Flame Spread Index (FSI) and Smoke Development Index (SDI)) : Class A ; Volatile Organic Compound : 6.4 g/L ; Dry Slip Resistance @ 23°C (UK SRG classification) : Low slip potential Solvent free, low odour, high build epoxy resin floor coating-Bahan Kimia dan Barang Kimia21.57
32.Nitoflor Hardtop Abrasion resistance ; Independently tested by the British Board of Agreement The test using an ‘A’ Court abrasion-testing machine (File No. M2/962) with nominal Compressive Strength 35 N/mm2, showed improves the abrasion resistance of concrete by 225%. Hardness (Mohs scale) : 7 on the Mohs original scale.Monolithic Surface Hardening Compound For Fresh Concrete Floors-Bahan Kimia dan Barang Kimia49.03
33.Nitoflor Lithurin MPenetration : Nitoflor Lithurin (M) is penetrative resulting in a more durable finish better than that of other surface treatments, which merely form a superficial skin. Hardness : The surface hardness is achieved through a chemical reaction within the cementitious material. Anti-dust : The chemical elimination of free lime and other soluble particles creates a tightly bound surface resistant to dusting. Chemical resistance: Nitoflor Lithurin (M) application reduces the absorbency of the surface and improves resistance to solvents, greases.Hardening and dust proofing compound for concrete surfaces-Bahan Kimia dan Barang Kimia73.41
34.Nitoflor Sl1000Mixed Specific Gravity : 1.70 g/cm3 Pot Life @ 23°C : 1 hour, @ 35°C: 30 mins ; Complete cure @ 23°C : 7 days, @ 35°C : 5 days Compressive strength 25°C 7 days (BS 6319 pt 2) : 85 N/mm2 Flexural strength @ 25°C 7 days (BS 6319 pt 3) :40 N/mm2 Tensile strength @ 25°C 7 days (BS 6319 pt 7) : 20 N/mm2 Adhesion strength (ASTM D412):1.5 N/mm² (Concrete failure) Application thickness : 0.5 - 1.5 mmFlow Applied 0.5 - 1.5mm Thick Epoxy Resin Based Floor Flooring -Bahan Kimia dan Barang Kimia14.71
35.Nitomortar Tc2000Properties at ambient Temperature @20°C ; Pot life :40 min Volume solids: 100% ; Pot life @ 24°C: 150 minutes (ASTM D2471:1999) ; Compressive strength: (ASTM C579:2018) : 1 day :30 N/mm² , 3 days : 50 N/mm² , 7 days : 70 N/mm² ; Flexural strength: (ASTM C580:2018) 7 days cured : 20 N/mm² ; Tensile strength: (ASTM C307:2018) 7 days cured : 14 N/mm² ; Mix density : 1.68 kg/L ; Thickness : Up to 3mm ; Adhesion to Concrete (ASTM D7234:2012) : > 2 N/mm2Epoxy resin based sealing compound-Bahan Kimia dan Barang Kimia24.48
36.Nitoprime 25Pot Life : @ 23°C : 2h, @ 35°C : 1h Average Drying Times : Touch : @ 23°C 4-5h, @ 35°C 3h ; Recoat : @ 23°C 6-8h, @ 35°C 4h To handle : @ 23°C 9-10h, @ 35°C 6hEpoxy Resin Primer For Flooring And Coating Range-Bahan Kimia dan Barang Kimia16.94
37.Nitoproof Aw Drying time (25+/-2°C): ~ 1 hour ; Specific Gravity (25+/-2°C) : 1.15 – 1.3 ; Viscosity (Brookfield, spindle 3, 60 rpm, 25+/-2°C) : 20 – 30 P ; Accelerated weathering Test -QUV 1000 hrs, ASTM G154 : pass ; Tensile- ASTM D882 > 2 kgf/cm2 ; Elongation - ASTM D882 >100% ; Water Vapour Transmission Rate , ASTM E96 2 - 5 g/m2/24 hrs ; Recommended coating: min. 2x coatingWeather resistant flexible acrylic Waterproofing-Bahan Kimia dan Barang Kimia79.04
38.Patchroc RspCompressive strength ASTM C109/C109M : 30-35 N/mm2 @ 4 hours; 40-50 N/mm2 @ 1 days; 51 – 60 N/mm2 @ 7 days; 61 - 70 N/mm2 @ 28 days Setting time - Initial set : 10-15 mins; Final set : 30-40 mins ; Traffic time : Pedestrian : 1-2 hours Vehicular : approx. 4 hours Flexural Strength : 30 -40 kg/cm2 at 4 hours; 55 - 65 kg/cm2 at 7 daysRapid Setting Patch Repair Concrete For Pavements And Floors-Bahan Kimia dan Barang Kimia26.16
39.Quicksocrete HpAppearance : Clear liquid ; Specific gravity, 25+/-2°C : 1.17 – 1.19Set accelerating concrete / mortar-Bahan Kimia dan Barang Kimia76.19
40.Renderoc Hb40Based on Laboratory Test at 23+/ 3°C, W/P = 0.16 ; Compressive strength 28 days 35 - 40 MPa Chloride ion content : Nil (not intentionally added)High Performance Fibre Reinforced Medium Weight Concrete Reinstatement Mortar-Bahan Kimia dan Barang Kimia24.03
41.Renderoc Hf PremixCompressive Strength ( ASTM C109 ) Tolerance ±10% : 30 N/mm2 @ 1 day, 50 N/mm2 @ 7 days, 60 N/mm2 @ 28 days Flexural Strength BS EN196-1 > 6 N/mm2 Rapid Chloride Permeability ASTM C1202 : LowFree Flowing Cementituous Repair Micro Concrete-Bahan Kimia dan Barang Kimia66.25
42.Renderoc PlugFollowing results obtained @ 23 ± 2°C, Tolerance +/-10% Compressive strength (ASTM C109/109M) : 5 N/mm2 @ 2 hours, 32 N/mm2 @ 28 days ; Initial set time : Approximately 1 minRapid Setting Cement Based, Water Stopping Mortar-Bahan Kimia dan Barang Kimia26.49
43.Renderoc RgPerformance at water to powder ratio of 0.18 and temperature of 25+/-2°C : Compressive strength (ASTM C109/C109M) = 26 N/mm2 @ 1 day With tolerance 10%, 55 N/mm2 @ 7 days, 65 N/mm2 @ 28 days ; Flexural strength (EN 196), tolerance min. 15% : 10 N/mm2 @ 28 days ; Fresh wet density : Approx. 2150 kg/m3 ; Expansion characteristics ASTM C940 : Up to 2% @ 24 hoursGeneral purpose non-shrink Cementitious Repair Mortar-Bahan Kimia dan Barang Kimia70.65
44.Renderoc Rg PremixPerformance at water: powder ratio of 0.126 and temperature of 23°± 3°C : Compressive strength : 26 N/mm2 @ 1 day with Tolerance ± 10% : 55 N/mm2 @ 7 days, 64 N/mm2 @ 28 days ; Time for expansion Start : 15 minutes, Finish : 2 hours ; Expansion characteristics : Up to 2% @ 24 hours (ASTM C940)General purpose non-shrink cementitious micro concrete-Bahan Kimia dan Barang Kimia72.70
45.Renderoc SmThe following results were obtained at w/p ratio of 0.12 and T 25+/- 2°C. Compressive strength Tolerance +/- 10% ASTM C109/C109M : 20 N/mm2 @ 1day, 45 N/mm2 @ 7 days, 55 N/mm2 @ 28 days Fresh wet density : Approx. 2200 gr/L Workability (Flow Table) : 19 – 24 cmModified Micro Concrete For Floor Repairs-Bahan Kimia dan Barang Kimia63.16
46.Renderoc Tg Properties at 23+/-2 °C Tolerance +/- 10% : Compressive Strength (ASTM C109/109M) : 40 N/mm2 at 28 days Setting Time : Dependent on temperature and water content typically 2 to 4 hours Chemical resistance : Slows-down chemical attack in aggressive environments.Trowel Grade Cemenituous Repair Mortar-Bahan Kimia dan Barang Kimia23.47

Pusat Peningkatan Penggunaan Produk Dalam Negeri

Gedung Kementerian Perindustrian lt. 3

Jl. Jenderal Gatot Subroto Kav. 52-53

Jakarta Selatan

Telp. 021 - 5255509 ext 4017

Contact Person: Arnes Lukman

PT. Surveyor Indonesia
 

Unit Bisnis Industri dan Fasilitas

Jl. Jend. Gatot Subroto Kav. 56, Lantai 7

Jakarta Selatan

Telp. 021 - 5265526 ext 818

Contact Person: Lebrina Eka Fitriani atau Raden Andini Putri

PT. Sucofindo (Persero)
 

Unit Bisnis Perdagangan, Industri, dan Kelautan

Bagian Fasilitasi Kandungan Lokal

Jl. Raya Pasar Minggu Km. 34, Lantai 4

Jakarta Selatan

Telp. 021 - 7983666 ext 2390

Contact Person: Nano Suprayogi atau Shasti

Dikelola Pusat Data dan Informasi Kementerian Perindustrian